ITS 220V AC Electric Circulation Pump

The ITS 220V Circulation Pump is designed for circulating heated liquids in solar water heating and similar circulation systems. The pump uses liquid-cooled bearings and requires water flow through the pump during operation to ensure proper cooling and lubrication of internal components.

The pump must never be operated without water flow, as running the unit dry or preventing liquid circulation during operation can cause damage to the pump bearings and internal components.

This 22mm ITS 220V AC Electric Circulation Pump is suitable for cold pressurized circulation of hot water under 110 degrees Centigrade. It is especially suited to operation in hot water heating systems, such as: Automatic pressurized and circulating water systems, solar water heating systems, water-cooled air-conditioning and central air-conditioning systems, water mains supply and liquid circulation for industrial equipment.

Features

This pump utilizes the benefits of stainless steel to keep moisture away from the electrical components. A Mechanical seal is not required, thus completely eliminating any possibility of leaking. The main components of the pump housing consist of high rigidity stainless steel for the motor shaft, graphite bearings. The water cycles between stator and rotor, this is not only for cooling, but also for bearing lubrication. The pump is noise free under normal operation. Advanced scientific design allows for continuous use of 30,000 hours trouble-free and maintenance-free. The features for this pump are: no noise, no vibration, no leaking, and long term maintenance free operation.

• 220–240V AC circulation pump
• Three-speed operation
• Wet rotor design
• Water lubricated bearings
• Quiet operation
• Suitable for solar water heating circulation systems and heating loops
• Brass pump body
• IP44 protection rating

Operating Conditions

• Pump bearings are liquid cooled during operation
• The pump must not be run without water flowing through it
• Preventing water flow while the pump is running will cause damage
• The surrounding ambient temperature must be lower than the temperature of the circulated liquid
• The circulation pump must be installed in a horizontal position
• The electrical connection may be positioned on the side or on top of the pump
• Electrical connections must be completed by a qualified electrician in accordance with SANS specifications
• After installation, all air must be bled from the pump before it is started

Dimensions

Overall Length 130 mm Width 125 mm Height 130 mm Pipe Connection ¾" BSP Union Size 22 mm

Hydraulic Performance

Speed Setting Power Consumption Max Flow Rate Max Head Speed I 46 W 35 L/min 4 m Speed II 67 W 45 L/min 5 m Speed III 93 W 55 L/min 6 m

Electrical Specifications

Voltage 220–240 V AC Frequency 50 Hz Protection Rating IP44 Insulation Class H Max Working Pressure 10 bar Max Fluid Temperature 110 °C Min Fluid Temperature 2 °C

Construction

Pump Body Brass Motor Housing Aluminium Impeller Engineering Polymer Bearings Water lubricated

Pump Replacement Procedure

1. Deactivate the mains power supply to the pump.
2. Ensure the shut-off valve at the opposite end of the pump is closed.
3. Check that the pump is not overheated before handling, as this could cause scalding.
4. Loosen and remove the pump.

Troubleshooting

Circulation pump will not start

Possible Cause Solution Power supply not connected / no power Check electrical connection and power supply Electric capacitor damaged Replace capacitor Rotating shaft stuck Loosen rotor with a screwdriver at the bleeding screw Impurity in rotating shaft chamber Disconnect pump, open chamber and clean

Noise from the circulation pump

Possible Cause Solution Air in the system Bleed air from the pump Impurities in the rotating chamber Disconnect pump, open chamber and clean

Warranty

The circulation pump carries a 12-month warranty from date of purchase.

• Warranty is carry-in and applies only to the original owner
• The pump must be returned in original packaging for inspection before warranty processing
• All operating procedures must be followed
• The pump is rated IP44
• It is not suitable for outdoor installation unless fully protected from environmental conditions
• The pump must be installed with an ITS approved non-return valve after the outlet

Warranty Exclusions

• Accidents, abuse or misuse
• Improper installation or maintenance
• Freezing, rust, corrosion or scale build-up in piping or internal components
• Lightning, electrical surges, blown fuses or open circuit breakers
• Wind or corrosive environments
• Failure to operate the pump according to ITS Solar written instructions

The warranty becomes null and void if the unit leaves South Africa unless prior approval is obtained from ITS Solar and Heat Pumps.